Showing results: 361 - 375 of 1660 items found.
-
DUST -
Singleton Corp.
Designed specifically to meet the SAE J 575 and GM 9103 P test standards. Used throughout industries to evaluate a component's ability to function in a dust filled atmosphere.
-
2401 -
The Eastern Specialty Company
TESCO’s Calibration Pulse Processor (Catalog No. 2401) adapts to any Next Generation three phase test board to directly calibrate with three independent single phase standards.
-
42090A -
Keysight Technologies
The 42090A is an open termination and is primarily used for performance tests of Keysight's 4-terminal pair LCR meters and impedance analyzers. Refer to the instrument's operation/service manual for the method of using this standard.
-
F-Squared Laboratories
If you are selling your product in the US and Canada, you need to comply with the applicable nationally accepted UL & CSA (and possibly other) standards. F2 Labs can evaluate and test your product, help you through the certification process and enable you to get your US and Canadian certifications to the UL and CSA standards.
-
GAO-ENET-103 -
GAO Tek Inc.
GAOTek Gigabit Ethernet Tester Module for 1G and 10G Packet is designed for installation and maintenance of Metro/Carrier Ethernet and IP services. It supplies a compact test solution for 1G and 10G packet Ethernet, including ITU-T Y.1564 standard for SLA and OAM test features.
-
CKT1175-20 -
CK Technologies, Inc.
The CKT1175-20 is a high-voltage wiring analysis system that features rack-mounted switching matrices. This system is expandable in 100 test point increments to 96,000 test points, and available with a wide variety of adapter cable interface connectors, with the standard interface being the CKT MAC interface system.
-
Kokusai Co., Ltd.
In Addition, The System Configuration Requires At Least 3 Main Units, A Control Panel, And A Controller, And Does Not Require Hydraulic Units Or Blowers. The Exciter Can Perform Standard Tests And Performance Tests Required For Automobile Seats Based On An Electric Servomotor Type Multi-Axis Vibration Tester.
-
Guangdong Bell Experiment Equipment Co.,Ltd
Walk in Chamber for Altitude Simulated Test Relative Standard test requirementsTest Object: battery pack and systemTest Conditions: Altitude 4000m or the equate air pressure condition, atroom temperature.The test objects stay in the test condition as Item 2 for 5 hours.Subject the test object to 1C(no more than 400A) constant current discharge until reaching the cutoff condition.After testing, observe for 2h under the room temperature.
-
146-P -
Electronic Specialties Inc.
These test leads feature stacking banana plug jacks, with extended 48" length. These are great for establishing connections to diagnostic test points, while allowing the connection to be tapped with other instruments...2 way connections. These feature high flexibility wire and standard 4mm size banana jacks. You will receive one red test lead and one black test lead. These test leads are compatible with Electronic Specialties 146 and 147 test lead kits.
-
Precision Milimeter Wave
Standard gain horns can be used to experimentally determine the gain of other antennas by using the substitution method. The standard gain horn and the antenna under test are alternately connected to a well matched detector system in order to compare their relative power levels. The power level difference is then added to the appropriate level of the calibration curve to determine the absolute gain of the antenna under test.View more Standard Gain Horn Antennas
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Rain test chambers for ingress protection testing simulates rain/water test as per IEC 60529 and DIN 40050-9((IP Code standard)) test standard. • IPX1 Protection against vertically dripping water• IPX2 Dripping water ± 15° from vertical• IPX3 Protection against spraying water• IPX4 Protection against splashing water• IPX5 Protection against low pressure jetting water• IPX6 Protection against high pressure jetting water• IPX7 Protection against temporary immersion• IPX8 Protection against continuous immersion• IPX9K Extremely high pressure jetting water
-
800 -
ACL Inc.
The ACL 800 Digital Megohmmeter is a dependable and easy-to-use audit kit that is designed to test static dissipative surfaces for electrical resistivity and resistance according to industry standards such as ANSI/ESD test methods S4.1, S7.1, and ASTM D257. Tests are easy to perform with or without the 5lb probes. Use optional concentric ring probe for conformance to STM11.11.
-
129610A -
Ametek Scientific Instruments
Liquid nitrogen (LN2) or liquid helium (LHe) can be used as the cryogen depending on the required operating temperature range. This allows standard tests to be performed using relatively low cost LN2 as the cryogen. Higher cost LHe can be substituted for the duration of tests where very low temperature is required, providing an economical solution to your test requirements.
-
ER-SERIES -
Envisys Technologies
ER-Series Rain Chambers are designed and manufactured to meet IP tests viz., IP Test (X1 to X8) IP Test (X4K, X6K & X9K) in different possible configurations ER-Series Rain Chambers are also built according to various other international standards viz., BIS, JIS, IEC-60529, EN, DIN, JSS-55555, MIL etc.,
-
141 -
STAR-Dundee
The SpaceWire Physical Layer Tester (SPLT) is a tool designed to test, validate and verify a SpaceWire system across all levels of the SpaceWire standard. Two SpaceWire ports employ a special LVDS interface which allows the transmitted signals to be deliberately and measurably manipulated to test the capability of a unit under test to receive signals of varying quality.